SII DPU-S series Guía de usuario

USER’S GUIDE Thermal Printer DPU-414 Read this manual carefully before using the printer. Keep this manual in a place where it can be

- 6 - Be sure to hold the battery cover to the printer when the battery pack is inserted in the printer. Fall of the battery pack due to the battery

- 7 - Precautions in the Battery pack (Option) WARNING If you find any of the following abnormalities in the battery pack, remove the battery pack f

- 8 - DO NOT apply strong impact to the battery pack with a hammer or a nail, and DO NOT crush it. Doing so may cause liquid leakage, explosion, ove

- 9 - OPERATING PRECAUTIONS Please follow the precautions below to enjoy and maintain the full performance of the printer. Using the printer  Be

- 10 -  Always use the specified thermal paper TP-411L. Installation  Install the printer in a flat, stable place.  Do not install the printe

- 11 - NOTATIONS USED IN THIS MANUAL The following two types of notations are used throughout this manual to denote items of caution and items to

- 12 -1 PREPARATION 1.1 Unpacking Once you have opened the carton, make sure it contains the printer and all accessories. The standard configurati

- 13 - 1.2 Part Names Front Paper coverwindowPaper coverPower SwitchPower LED Back Parallel inputconnectorSerial inputconnectorPower supply jackGro

- 14 - 1.3 Operation Panel 1 Power Switch Slide the Power Switch to turn the power on (ONLINE) or off. 2 FEED button Feeds the thermal paper wh

- 15 -  DO NOT press and hold the ONLINE button and FEED button for 30 seconds or more, because it will cause the Software DIP switches to reset an

DPU-414 THERMAL PRINTER USER’S GUIDE Document Number U00120592100 First Edition June 2010 Copyright 2010 by Seiko Instruments Inc. A

- 16 -2 OPERATION 2.1 Connecting AC Adapter 1. Turn off the power. 2. Plug the DC plug on the AC adapter into the power supply jack on the

- 17 -2.2 Loading the Thermal Paper Opening and Closing the Paper Cover 1. Lightly push up on the front of the paper cover with your thumb and ro

- 18 -Loading the Thermal Paper 1. Turn on the power. 2. Cut the tip of the thermal paper straight across. New paper can be inserted as is. (See

- 19 -2.3 Setting the Software DIP Switches (SWDIP switch) The startup settings and input method can be set by the Software DIP switches (SWDIP swi

- 20 -complete!!” is printed out and the printer returns to ONLINE mode. 6. As soon as switch number 8 of SWDIP switch 3 is set, the printer writes

- 21 -2.4 SWDIP Switch Settings (1) SWDIP switch 1 indicates factory default setting. Switch No. Function ON OFF 1 Input Method Parallel Ser

- 22 -(2) SWDIP switch 2 Switch No. Function ON OFF 1 Print mode Normal printing (40 columns) Condensed printing (80 columns) 2 User-defined char

- 23 - (3) SWDIP switch 3 Switch No. Function ON OFF 1 Data bit length 8 bits 7 bits 2 Parity permission Without With 3 Parity condition Odd

- 24 -2.5 Connecting the Printer Connection 1. Turn off the printer and computer. 2. Connect the printer to the computer with an interface cable.

- 25 -Parallel Serial

Applicable EC Directive and Standards Product: Thermal Printer DPU-414-40B-E, DPU-414-41B-E Directive: Title 2004/108/EC EC Electromagnetic Comp

- 26 -2.6 Test Print In a test print, characters 20H to FEH are printed in condensed, ordinary and double-width modes according to the internation

- 27 -2.7 HEX Dump Print Data input from the computer is printed in hexadecimal codes and in characters to allow you to check if data has been in

- 28 -2.8 Printing 1. Turn on the power to the printer and the computer. 2. Check that the ONLINE LED lights. When the thermal paper is not set,

- 29 -2.10 Handling the Battery Pack A fully charged battery pack can print about 3000 lines (40 columns of the number ”8”). The battery discharges

- 30 -Removing the Battery Pack 1. Remove the battery cover as shown in Figure 1. 2. Pull out the battery pack, grab the connector with your thumb

- 31 -When the Battery pack Gets Low During Printing When the Power LED starts blinking about once every 0.5 seconds and the printer goes OFFLINE, co

- 32 -3 PRINTER FUNCTION 3.1 Buffer Full Printing The DPU-414 has a line buffer to receive data in one-line units. If data with more columns t

- 33 -If an error occurs: A or B: 1. Turn off the Power Switch. 2. Remove the foreign material. 3. Turn on the Power Switch. C: Use the pri

- 34 -4 CONTROL CODE The DPU-414 uses control codes to change forms and characters. The control codes are not printed. There are two types of f

- 35 -ESC sequence codes Code Function ESC+ ”%” +n Select user-definable characters ESC+ ”&” +s+n Register user-definable characters ESC+ ”:”

Federal Communications Commission (FCC) compliance statement This equipment has been tested and found to comply with the limits for a Class B digital

- 36 -5 CHARACTER CODE TABLE  Japanese Character Set The following table is the Japanese character set when 0 is set to normal 0.

- 37 - IBM Character Set The following table is the English character set when 0 is set to normal 0 . • SP denotes space. • B

- 38 - 6 SPECIFICATIONS 6.1 General Specifications Printer specifications Printing method : Thermal serial dot Character mode Total number of do

- 39 - Specifications of Specified AC Adapter (Option) Item Specifications Product No. PW-4007-JU1-E Input 100VAC to 120VAC 50Hz to 60Hz Output

- 40 -Specifications of the AC Cable (Option PW-4007-JU1-E only) Item Specifications Product No. CB-US04-18A-E Cable length Approx. 1.75m Regulat

- 41 - List of Compliance with Regulation Please check the list below to see if the printer and its accessories can be operated in destination coun

- 42 -6.2 Interface Specifications Parallel (1) Specifications Data input : 8 bits parallel (Centronics) Handshake: STROBE , BUSY, and ACK (2)

- 43 -(3) Data Input Timing (Unit: s, typical) (4) Signal Conditions Standard Item Min. Typ. Max. Unit Input : Low Level Voltage 0.0  0.9 V I

- 44 -Serial (1) Specifications Data input : RS-232C Data control : H/W BUSY, XON/XOFF (2) Connector signal description Pin no. Signal I/O F

- 45 -(3) Error processing The following characters are printed when an error occurs. ? (3FH) : Framing error ! (21H) : Parity error * (2AH) : Ove

- 1 - INTRODUCTION Thank you for purchasing the DPU-414 thermal printer. This USER’S GUIDE explains how to handle DPU-414 thermal printer (here

- 46 - 7 TROUBLESHOOTING Check the following points if the printer has malfunctioned or does not operate at all. If it has still problems, call

- 47 -If the printer does not print or stops during printing Checkpoint Action Reference page Is the OFFLINE LED flashing? The thermal paper has ru

- 48 -If the printer prints wrong characters Checkpoint Action Reference page Is interface cable connected correctly? See Section 2.5. 24 Are the

- 49 -8 CARING FOR THE DPU-414 PRINTER If the outside of your printer gets dirty, wipe it with a soft, dry cloth. If it gets very dirty, wet

Seiko Instruments Inc. 1-8, Nakase, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan Print System Division Telephone:+81-43-211-1106 Facsimile

- 2 - SAFETY PRECAUTIONS The following symbols are used in this manual in order to make use of the printer properly and prevent the printer from

- 3 - Precautions in the Printer WARNING DO NOT use the printer, the AC adapter and the AC cable in countries where these items do not comply with t

- 4 - DO NOT put the printer into water in a place where it could get wet. Doing so may cause fire, a failure or other accidents. DO NOT touch t

- 5 -CAUTION If the printer is not used for a long time, unplug the AC plug from the outlet and remove the battery pack from the printer. If not, it